VDSL-LINE-EXT-SCM-MIB DEFINITIONS ::= BEGIN
 
IMPORTS
 
MODULE-IDENTITY,
OBJECT-TYPE,
Integer32,
transmission,
Unsigned32                      FROM SNMPv2-SMI         -- [RFC2578]
TEXTUAL-CONVENTION,
TruthValue,
RowStatus                       FROM SNMPv2-TC          -- [RFC2579]
MODULE-COMPLIANCE,
OBJECT-GROUP                    FROM SNMPv2-CONF        -- [RFC2580]
ifIndex                         FROM IF-MIB             -- [RFC2863]
vdslLineConfProfileName         FROM VDSL-LINE-MIB;     -- [RFC3728]
 
vdslExtSCMMIB MODULE-IDENTITY
   LAST-UPDATED "200504280000Z" --     April 28, 2005
   ORGANIZATION "ADSLMIB Working Group"
   CONTACT-INFO "WG-email:  adslmib@ietf.org
         Info:      https://www1.ietf.org/mailman/listinfo/adslmib
 
         Chair:     Mike Sneed
                    Sand Channel Systems
         Postal:    P.O. Box 37324
                    Raleigh NC 27627-732
         Email:     sneedmike@hotmail.com
         Phone:     +1 206 600 7022
 
         Co-Chair/Co-editor:
                    Bob Ray
                    PESA Switching Systems, Inc.
         Postal:    330-A Wynn Drive
                    Huntsville, AL 35805
                    USA
         Email:     rray@pesa.com
         Phone:     +1 256 726 9200 ext.  142
 
 
 
         Co-editor: Menachem Dodge
                    ECI Telecom Ltd.
         Postal:    30 Hasivim St.
                    Petach Tikva 49517,
                    Israel
         Email:     mbdodge@ieee.org
         Phone:     +972 3 926 8421
        "
 
DESCRIPTION
   "The VDSL-LINE-MIB found in RFC 3728 defines objects for the
   management of a pair of VDSL transceivers at each end of the VDSL
   line.  The VDSL-LINE-MIB configures and monitors the line code
   independent parameters (TC layer) of the VDSL line.  This MIB
   module is an optional extension of the VDSL-LINE-MIB and defines
   objects for configuration and monitoring of the line code specific
   (LCS) elements (PMD layer) for VDSL lines using SCM coding.  The
   objects in this extension MIB MUST NOT be used for VDSL lines
   using Multiple Carrier Modulation (MCM) line coding.  If an object
   in this extension MIB is referenced by a line which does not use
   SCM, it has no effect on the operation of that line.
 
   Naming Conventions:
 
      Vtuc -- VDSL transceiver at near (Central) end of line
      Vtur -- VDSL transceiver at Remote end of line
      Vtu  -- One of either Vtuc or Vtur
      Curr -- Current
      Atn  -- Attenuation
      LCS  -- Line Code Specific
      Max  -- Maximum
      Mgn  -- Margin
      PSD  -- Power Spectral Density
      Rx   -- Receive
      Snr  -- Signal to Noise Ratio
      Tx   -- Transmit
 
   Copyright (C) The Internet Society (2005).  This version
   of this MIB module is part of RFC 4069: see the RFC
   itself for full legal notices."
           REVISION "200504280000Z" --     April 28, 2005
           DESCRIPTION "Initial version, published as RFC 4069."
       ::= { transmission 228 }
 
       vdslLineExtSCMMib    OBJECT IDENTIFIER ::= { vdslExtSCMMIB 1 }
       vdslLineExtSCMMibObjects OBJECT IDENTIFIER ::=
                                              { vdslLineExtSCMMib 1 }
--
 
 
 
-- textual conventions used in this MIB
--
 
VdslSCMBandId ::= TEXTUAL-CONVENTION
    STATUS       current
    DESCRIPTION
       "This data type is used as the syntax for the VDSL SCM Band
        Identity.  Attributes with this syntax identify the SCM Band
        referred to.  Specified as an INTEGER, the possible values
        are:
 
        optionalBand (1)  -- the optional Band range [25kHz - 138kHz]
        firstDownstreamBand (2)  -- first Downstream Band
        firstUpstreamBand (3)    -- first Upstream Band
        secondDownstreamBand (4) -- second Downstream Band
        secondUpstreamBand (5)   -- second Upstream Band
        thirdDownstreamBand (6)  -- third Downstream Band
        thirdUpstreamBand (7)    -- third Upstream Band"
 
 
    SYNTAX      INTEGER       {  optionalBand (1),
                                 firstDownstreamBand (2),
                                 firstUpstreamBand (3),
                                 secondDownstreamBand (4),
                                 secondUpstreamBand (5),
                                 thirdDownstreamBand (6),
                                 thirdUpstreamBand(7) }
 
--
-- Single carrier modulation (SCM) configuration profile tables
--
 
vdslLineSCMConfProfileBandTable OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslLineSCMConfProfileBandEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
       "This table contains transmit band descriptor configuration
        information for a VDSL line.  Each entry in this table
        reflects the configuration for one of possibly many bands
        of a single carrier modulation (SCM) VDSL line.  For each
        profile which is associated with a VDSL line using SCM
        line coding, five entries in this table will exist, one for
        each of the five bands.  Bands which are not in use will be
        marked as unused.  These entries are defined by a manager
        and can be used to configure the VDSL line.  If an entry in
 
 
 
 
 
        this table is referenced by a line which does not use SCM,
        it has no effect on the operation of that line."
    ::= { vdslLineExtSCMMibObjects 1 }
 
vdslLineSCMConfProfileBandEntry OBJECT-TYPE
    SYNTAX       VdslLineSCMConfProfileBandEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
       "Each entry consists of a list of parameters that
        represents the configuration of a single carrier
        modulation VDSL modem transmit band.
 
        A default profile with an index of 'DEFVAL', will
        always exist and its parameters will be set to vendor
        specific values, unless otherwise specified in this
        document.
 
        All read-create objects defined in this MIB module SHOULD be
        stored persistently."
 
    INDEX { vdslLineConfProfileName,
     vdslLineSCMConfProfileBandId }
    ::= { vdslLineSCMConfProfileBandTable 1 }
 
VdslLineSCMConfProfileBandEntry ::=
    SEQUENCE
       {
       vdslLineSCMConfProfileBandId                VdslSCMBandId,
       vdslLineSCMConfProfileBandInUse             TruthValue,
       vdslLineSCMConfProfileBandCenterFrequency   Unsigned32,
       vdslLineSCMConfProfileBandSymbolRate        Unsigned32,
       vdslLineSCMConfProfileBandConstellationSize Unsigned32,
       vdslLineSCMConfProfileBandTransmitPSDLevel  Unsigned32,
       vdslLineSCMConfProfileBandRowStatus         RowStatus
       }
 
vdslLineSCMConfProfileBandId OBJECT-TYPE
    SYNTAX      VdslSCMBandId
    MAX-ACCESS  not-accessible
    STATUS  current
    DESCRIPTION
       "The BandId for this entry, which specifies which band
        is being referred to."
    ::= { vdslLineSCMConfProfileBandEntry 1 }
 
 
 
 
 
 
vdslLineSCMConfProfileBandInUse OBJECT-TYPE
    SYNTAX       TruthValue
    MAX-ACCESS   read-create
    STATUS  current
    DESCRIPTION
       "Indicates whether this band is in use.
        If set to True this band is in use."
    ::= { vdslLineSCMConfProfileBandEntry 2 }
 
vdslLineSCMConfProfileBandCenterFrequency OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "Hz"
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
       "Specifies the center frequency in Hz"
    REFERENCE    "T1E1.4/2000-011R3"    -- Part 2, SCM
    ::= { vdslLineSCMConfProfileBandEntry 3 }
 
vdslLineSCMConfProfileBandSymbolRate OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "baud"
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
       "The requested symbol rate in baud."
    REFERENCE    "T1E1.4/2000-011R3"    -- Part 2, SCM
    ::= { vdslLineSCMConfProfileBandEntry 4 }
 
vdslLineSCMConfProfileBandConstellationSize OBJECT-TYPE
    SYNTAX       Unsigned32 (0..16)
    UNITS        "log2"
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
       "Specifies the constellation size."
    REFERENCE    "T1E1.4/2000-011R3"    -- Part 2, SCM
    ::= { vdslLineSCMConfProfileBandEntry 5 }
 
 
 
 
 
 
 
 
 
 
 
 
 
vdslLineSCMConfProfileBandTransmitPSDLevel OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "-0.25 dBm/Hz"
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
       "The requested transmit power spectral density for the VDSL
        modem.  The Actual value in -0.25 dBm/Hz."
    REFERENCE    "T1E1.4/2000-011R3"    -- Part 2, SCM
    ::= { vdslLineSCMConfProfileBandEntry 6  }
 
vdslLineSCMConfProfileBandRowStatus OBJECT-TYPE
    SYNTAX       RowStatus
    MAX-ACCESS   read-create
    STATUS       current
    DESCRIPTION
       "This object is used to create a new row or modify or
        delete an existing row in this table.
 
        A profile activated by setting this object to `active'.
        When `active' is set, the system will validate the profile.
 
        None of the columns in this row may be modified while the
        row is in the `active' state.
 
        Before a profile can be deleted or taken out of
        service, (by setting this object to `destroy' or
        `notInService') it must be first unreferenced
        from all associated lines."
 
    ::= { vdslLineSCMConfProfileBandEntry 7 }
 
--
-- SCM physical band
--
 
vdslLineSCMPhysBandTable OBJECT-TYPE
    SYNTAX       SEQUENCE OF VdslLineSCMPhysBandEntry
    MAX-ACCESS   not-accessible
    STATUS       current
    DESCRIPTION
       "This table provides one row for each SCM Vtu band.  This
        table is read only as it reflects the current physical
        parameters of each band.  For each ifIndex which is
        associated with a VDSL line using SCM line coding, five
        entries in this table will exist, one for each of the
        five bands.  Bands which are not in use will be marked
        as unused."
 
 
 
    ::= { vdslLineExtSCMMibObjects 2 }
 
vdslLineSCMPhysBandEntry OBJECT-TYPE
    SYNTAX        VdslLineSCMPhysBandEntry
    MAX-ACCESS    not-accessible
    STATUS        current
    DESCRIPTION
       "An entry in the vdslLineSCMPhysBandTable."
    INDEX { ifIndex,
            vdslLineSCMPhysBandId  }
    ::= { vdslLineSCMPhysBandTable 1 }
 
VdslLineSCMPhysBandEntry ::=
    SEQUENCE
        {
        vdslLineSCMPhysBandId                    VdslSCMBandId,
        vdslLineSCMPhysBandInUse                 TruthValue,
        vdslLineSCMPhysBandCurrCenterFrequency   Unsigned32,
        vdslLineSCMPhysBandCurrSymbolRate        Unsigned32,
        vdslLineSCMPhysBandCurrConstellationSize Unsigned32,
        vdslLineSCMPhysBandCurrPSDLevel          Unsigned32,
        vdslLineSCMPhysBandCurrSnrMgn            Integer32,
        vdslLineSCMPhysBandCurrAtn               Unsigned32
        }
 
vdslLineSCMPhysBandId OBJECT-TYPE
    SYNTAX      VdslSCMBandId
    MAX-ACCESS  not-accessible
    STATUS  current
    DESCRIPTION
        "The BandId for this entry, which specifies which band
         is being referred to."
    ::= { vdslLineSCMPhysBandEntry 1 }
 
vdslLineSCMPhysBandInUse OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-only
    STATUS  current
    DESCRIPTION
       "Indicates whether this band is in use.
        If set to True this band is in use."
    ::= { vdslLineSCMPhysBandEntry 2 }
 
 
 
 
 
 
 
 
 
vdslLineSCMPhysBandCurrCenterFrequency OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "Hz"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
       "The current center frequency in Hz for this band."
    REFERENCE    "T1E1.4/2000-011R3"    -- Part 2, SCM
    ::= { vdslLineSCMPhysBandEntry 3 }
 
vdslLineSCMPhysBandCurrSymbolRate    OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "baud"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
       "The current value of the symbol rate in baud for this
        band."
   REFERENCE    "T1E1.4/2000-011R3"    -- Part 2, SCM
   ::= { vdslLineSCMPhysBandEntry 4 }
 
vdslLineSCMPhysBandCurrConstellationSize OBJECT-TYPE
    SYNTAX       Unsigned32 (0..16)
    UNITS        "log2"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
       "The current constellation size on this band."
    REFERENCE    "T1E1.4/2000-011R3"    -- Part 2, SCM
    ::= { vdslLineSCMPhysBandEntry 5 }
 
vdslLineSCMPhysBandCurrPSDLevel    OBJECT-TYPE
    SYNTAX       Unsigned32
    UNITS        "- 0.25 dBm/Hz"
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
       "The transmit power spectral density for the
        VDSL modem."
    REFERENCE    "T1E1.4/2000-011R3"    -- Part 2, SCM
    ::= { vdslLineSCMPhysBandEntry 6 }
 
 
 
 
 
 
 
 
 
 
vdslLineSCMPhysBandCurrSnrMgn OBJECT-TYPE
    SYNTAX        Integer32
    UNITS         "0.25 dB"
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
       "Noise margin as seen by this Vtu and band with respect
        to its received signal in 0.25 dB."
    ::= { vdslLineSCMPhysBandEntry 7 }
 
vdslLineSCMPhysBandCurrAtn OBJECT-TYPE
    SYNTAX        Unsigned32 (0..255)
    UNITS         "0.25 dB"
    MAX-ACCESS    read-only
    STATUS        current
    DESCRIPTION
       "Measured difference in the total power transmitted by
        the peer Vtu on this band and the total power received
        by this Vtu on this band in 0.25 dB."
    ::= { vdslLineSCMPhysBandEntry 8 }
 
-- conformance information
 
vdslLineExtSCMConformance OBJECT IDENTIFIER ::=
                                            { vdslLineExtSCMMib 2 }
vdslLineExtSCMGroups OBJECT IDENTIFIER ::=
                                    { vdslLineExtSCMConformance 1 }
vdslLineExtSCMCompliances OBJECT IDENTIFIER ::=
                                    { vdslLineExtSCMConformance 2 }
 
vdslLineExtSCMMibCompliance MODULE-COMPLIANCE
    STATUS  current
    DESCRIPTION
       "The compliance statement for SNMP entities which
        manage VDSL interfaces."
 
    MODULE  -- this module
 
    MANDATORY-GROUPS
    {
      vdslLineExtSCMGroup
    }
 
    ::= { vdslLineExtSCMCompliances 1 }
 
 
 
 
 
 
 
-- units of conformance
 
vdslLineExtSCMGroup    OBJECT-GROUP
    OBJECTS
        {
        vdslLineSCMConfProfileBandInUse,
        vdslLineSCMConfProfileBandTransmitPSDLevel,
        vdslLineSCMConfProfileBandSymbolRate,
        vdslLineSCMConfProfileBandConstellationSize,
        vdslLineSCMConfProfileBandCenterFrequency,
        vdslLineSCMConfProfileBandRowStatus,
        vdslLineSCMPhysBandInUse,
        vdslLineSCMPhysBandCurrPSDLevel,
        vdslLineSCMPhysBandCurrSymbolRate,
        vdslLineSCMPhysBandCurrConstellationSize,
        vdslLineSCMPhysBandCurrCenterFrequency,
        vdslLineSCMPhysBandCurrSnrMgn,
        vdslLineSCMPhysBandCurrAtn
 
        }
    STATUS      current
    DESCRIPTION
       "A collection of objects providing configuration
        information for a VDSL line based upon single carrier
        modulation modem."
    ::= { vdslLineExtSCMGroups 1 }
 
END